Yes, the spindles that come on the Dexter Trailer Axle Beam with EZ-Lube Spindles # T3584F-EZ-8974 are the number 84 spindles.
For a brake drum confirmed to fit this spindle you could use the # 84546UC3. For an idler hub you could use the # 84545BX. Both these have 5 on 4-1/2 inch bolt patterns for the wheel lugs and I attached review videos for both. view full answer...
The inner and outer bearings, races, seals and cap are all included. We carry three spindles that will fit this hub. The differences is the shanks that are to be welded to the axle, but the machined portions will fit the hub assembly you were looking at.
The spindles are part # TRU94FR, part # TRU59FR, and part # TRU97FR. view full answer...
The Timbren Axle-Less Trailer Suspension System # TASR5200S03 does included both a left and a right side. The 4 inch lift spindle does mean that it will raise the trailer 4 inches. If you need the trailer lower there is a version with 4 inch drop spindles, # ASR5200S04. view full answer...
The Bearing Kit # BK1-150 contains the bearings, races and grease seal commonly found on a BTR Spindle.
The Bearing Kit # BK1-100 contains the bearings, races and grease seal commonly found on a BT8 Spindle.
It appears that your spindle on your 2002 Karavan PWC Trailer uses a combination of the two kits. As we do not have an exact kit with the components that you need you can acquire all the parts individually. You will need the following parts for both hubs on your axle.
4- # L44649... view full answer...
Appreciate the purchase of the Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs # e32GR.
This axle and hub combo does not come with a spindle washer, and one is not actually needed as the castle nut pushes directly onto the idler hub bearing. view full answer...
The Electric Trailer Brake Kit # AKEBRK-35-SA does not include the drums. If you happen to need a new hub and drum assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. You also need to know is what spindle you have on your trailer.
To do that you can either get the inner and outer bearing numbers from a hub or use a dial caliper to get exact measurements of the spindle, both bearing... view full answer...
The Electric Trailer Brake Kit # AKEBRK-35-SA only includes the left and right side brake assemblies for one axle. You will need 2 hub/drums like the Easy Grease Trailer Hub and Drum Assembly # AKHD-545-35-EZ-K which fits a standard #84 spindle which is found on most 3,500lb trailer axles. These hubs have a 5 on 4-1/2" bolt pattern. If you have a different size spindle or bolt pattern please let me know and I can help you find the correct hub/drums. view full answer...
No, the Timbren Axle-Less Trailer Suspension - Heavy Duty - 4" Lift - 4 Bolt Flange - 2,200 lbs # TASR1THDS04 is not available without the spindles. view full answer...
Actually the Timbren Heavy-Duty Axle-Less Trailer Suspension # ASR2KHDS03 comes with castle nuts, spindle washers, and cotter pins so you would not need to purchase them separately.
I attached a picture that shows them all pointed out. view full answer...
Parts # AKEBRK-35L and # AKEBRK-35R are left and right hand 10 inch brake assemblies for 3,500 pound trailer axles. Use # AKEBRK-35 to purchase both of them together.
The hub and drum assemblies and the bearing kits are not included. A 3,500 pound axle that uses 10 inch brakes and has a 5 on 4-1/2 bolt pattern likely uses bearings # L44649 and # L68149. You'll want to verify these are the correct numbers on your trailer. If they are then the hubs you need are # AKHD-545-35-EZ-K for... view full answer...
The Timbren Axle-Less Suspension System you referred to, part # A35RS545E includes the following:
Aeon Spring Assemblies
EZ Lube Spindle Assemblies
Castle Nuts and Washers for Spindles
Inner and Outer Bearings
Inner and Outer Races
Grease Seals
EZ Lube Grease Caps
5 Lug on 4-1/2 Bolt Circle Brake Drum
Electric Brake Assemblies
I have taken a photo from the product description page that shows everything that is included. view full answer...
The brake hub/drums are sold separately from the hub/drums.
The # AKEBRK-35-SA 10 inch self adjusting trailer brake assemblies are compatible with a 10 x 2-1/4 inch brake hub/drum usually found on a 3500 lb axle. The spindles of a 3500 lb axle are typically compatible with a L44649 outer and a L68149 inner wheel bearing and a grease seal with a 1.719 ID and a 2.565 inch OD. Most 3500 lb rated hubs would use a 5 lug on 4-1/2 inch bolt pattern.
So, I'd recommend checking the reference numbers... view full answer...
Some spindles similar to # TRU74FR is going to have the brake mounting flange welded onto it. The Brake mounting flange gets welded to the end of the axle to provide a secure mounting place for brake assemblies. It's a normal setup. It's not uncommon to have a round into a square axle, but you can replacement if you see fit. view full answer...
Yes, when you purchase the Timbren Axle-Less Trailer Suspension System like part # A20RS440 both sides are included in the package.
This system has a 2000-lb weight capacity and includes the EZ Lube spindles with the bearings, races, and seals. view full answer...
Actually the Trailer Hub Assembly # 8-247-50UC3-EZ that you referenced comes with a grease cap already with a removable rubber plug that will give you access to the zerk fitting of the spindle that will make lubing the bearings very easy.
I attached a link to the video you referenced as well. view full answer...
Yes, the Timbren Axle-Less System part # ASR5200S01 does come with 5 bolt mounting flanges.
I attached a picture that shows the flange behind the spindle. view full answer...
The Dexter Utility Trailer Hub and Drum Assembly # 8-174-5UC3 includes a grease seal with an inner diameter of 2.125-inches. This is noted in the bearing/race/seal information that appears on the hub's page under the specs. The seal outer diameter, which matches the hub's bore, is 3.376-inches. Seal dimensions must be very precise and should be taken to the nearest thousandth of an inch, such as 2.125-inches, by using a precision caliper like # PTW80157.
This hub has 9/16-inch wheel studs... view full answer...
The Dexter Trailer Hub and Drum Assembly part # 84546UC3-EZ comes with the nut and retainer clip or you can purchase the Spindle Nut Kit for EZ Lube Axles part # RG05-100 which comes with the nut, retainer clip, and d-ring washer. You can reuse the old washer. view full answer...
The Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3.5K # 23-468-469 do not come with the brake hub/drum. Because these are the 3,500 lb axle kits, I can confirm that the Dexter drums for these assemblies are the Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 # 84546UC3 or if your spindles have the integrated grease zerk # AKHD-545-35-EZ-K.
I've attached an article to help further with bearings and seals to... view full answer...
The Dexter Trailer Hub Assembly, part # 42655UC1 does include the hub as well as the bearings, races, seal, grease cap, wheel bolts and lug nuts. I am sorry you found this out after you purchased this somewhere else.
This hub is designed to fit 6,000 lb axles with spindles that need a grease seal with a 2-1/4 inch inner diameter. I have attached a link to a product review for this hub you can check out. view full answer...